Search found 33 matches

by PlasticMetal
Tue Apr 09, 2019 10:18 pm
Forum: RailCore Build Support
Topic: Drivers over temp
Replies: 2
Views: 97

Re: Drivers over temp

Unfortunately, I haven't got any answers for you, but my suggestion would be to post this question on the Duet forum, if you haven't already.
by PlasticMetal
Sat Apr 06, 2019 10:18 pm
Forum: ShowOff
Topic: My RailCore
Replies: 13
Views: 1144

Re: My RailCore

Thank you. While the yellow stands out better, I've since repainted it in red, to more closely match the kit printed parts. I also discovered that it's much easier to apply the paint using a small plastic syringe, like off eBay or Amazon. That worked for the majority of each letter, but then I did u...
by PlasticMetal
Sun Mar 24, 2019 9:40 am
Forum: RailCore Build Support
Topic: What to look for in linear rails
Replies: 16
Views: 805

Re: What to look for in linear rails

Looks great, especially at that speed!
by PlasticMetal
Wed Mar 13, 2019 9:50 am
Forum: RailCore Build Support
Topic: What to look for in linear rails
Replies: 16
Views: 805

Re: What to look for in linear rails

Mine is partially torn down right now after I re-squared the frame (finally got some 1-2-3 blocks). In the process, one of the carriages partially slid off its rail and dumped some bearings. So, I'm going to clean and re-lube likely all 3 Z carriages soon. Tony (kraegar) told me over on Discord that...
by PlasticMetal
Fri Mar 08, 2019 8:53 pm
Forum: ShowOff
Topic: My RailCore
Replies: 13
Views: 1144

Re: My RailCore

I had bought yellow paint before the printer arrived, forgetting it shipped with red printed parts, but I used it anyway. I currently have the printer torn apart to 1) better square up the frame, and 2) install aluminum Z yokes and LED strip lights, so I plan on painting red over the yellow. The yel...
by PlasticMetal
Sun Feb 03, 2019 3:54 am
Forum: BuildLogs
Topic: Dual extrusion Railcore 2
Replies: 4
Views: 312

Re: Dual extrusion Railcore 2

Nice!
by PlasticMetal
Sun Jan 27, 2019 11:17 pm
Forum: Firmware and Configuration
Topic: Duet and Simplify3D setup for dual extrusion.
Replies: 11
Views: 503

Re: Duet and Simplify3D setup for dual extrusion.

Suggestion to check wiring pairs deleted. Looks like we were posting at almost the same time.
by PlasticMetal
Sun Jan 27, 2019 6:37 pm
Forum: Firmware and Configuration
Topic: Duet and Simplify3D setup for dual extrusion.
Replies: 11
Views: 503

Re: Duet and Simplify3D setup for dual extrusion.

Does this help? https://www.bondtech.se/en/customer-service/faq/

Go down to the e-step section. The values are for 1.8deg steppers, double for 0.9.
by PlasticMetal
Fri Jan 25, 2019 11:58 pm
Forum: BuildLogs
Topic: Project R3D built machine with mods
Replies: 28
Views: 1226

Re: Project R3D built machine with mods

On my delta, I have G29 S1 in the starting gcode for each job, though it could go in config.g, but then its only potentially available after each boot of the Duet.

Either way, yes, you have to define a grid, in config.g. The M557 would have to come before G29, if G29 is also in config.g.
by PlasticMetal
Fri Jan 25, 2019 12:03 am
Forum: RailCore Build Support
Topic: Dual Filament
Replies: 6
Views: 401

Re: Dual Filament

David - just a quick note to thank you for visiting this forum. You've been a big help to me over on your Duet forum. I honestly don't know where you find the time for all your activities.